LogoLogo
  • Introducción
  • PRIMEROS PASOS
    • Menú Principal
    • Descargar la Aplicación
    • Conectar el dispositivo Moasure
    • Montar y utilizar el Moasure STICK
  • dispositivo Moasure
    • Menú Principal
    • Cargar el dispositivo Moasure
    • Encender/Apagar el dispositivo Moasure
    • Qué significa cada indicador LED
    • Punto de referencia
    • Todo sobre la exactitud y precisión
    • Tiempo de medición / Exactitud
    • Técnica de medición
      • Domine el Ritmo
      • Domine la Colocación
      • Domine la Rotación
    • Actualizador de Firmware
  • Aplicación Moasure
    • Menú Principal
    • Iniciar y Finalizar una medición
    • Guardar una medición
    • Exportar una medición
    • Tipos de medición
    • Tipos de rutas
    • Tipos de vistas
    • Consultar puntos y lados
    • Cómo crear Capas
    • Herramientas de Edición
      • Abrir / Cerrar
      • Cuadrar
      • Crear Punto de Interés
      • Editar Imagen de Fondo
      • Extrapolar Esquina
      • Ignorar
      • Ignorar Automáticamente
      • Editar Inicio
      • Editar Rutas
      • Corte/Relleno
      • Añadir Profundidad
    • Ajustes
      • Accesorio Moasure STICK
      • Unidades de medida
      • Tipo de ruta: Cómo iniciar una medición
      • Opciones para el tipo de ruta 'Trazar'
      • Ignorar Automáticamente
      • Cómo silenciar el audio de la medición
      • Opciones de Visualización
        • Tema
        • Tamaño de Fuente
        • Instructor de Moasure
        • Mostrar orientación y colocación del dispositivo en diagramas
        • Preferencias de Exportación
      • Gestión de Cuentas
        • Habilitar / Deshabilitar Análisis
        • Cerrar Sesión
        • Restablecer Configuración
        • Eliminar Cuenta
      • Gestión de Dispositivos
        • Añadir Dispositivo
        • Eliminar Dispositivo
        • Cómo cambiar el dispositivo seleccionado
        • Cómo cambiar el método de encendido
        • Cómo cambiar el tiempo de desconexión del dispositivo
      • Cómo enviar una Solicitud de Ayuda
  • CASOS DE USO
    • Menú Principal
    • Tu primera medición: área y perímetro
    • Cómo medir un campo de golf
    • Cómo medir una cubierta/tarima en minutos
    • Demostración completa en exteriores
    • Cómo medir un camino de acceso
    • Cómo hacer un replanteo
    • Cómo medir un jardín complejo
    • Measure Tree or Sprinkler Locations on a Lawn
    • Measure Volume and 3D Terrain
    • Cómo medir piscinas rápidamente
    • Cómo medir con rapidez un parque infantil
    • Measure Elevation
    • Measure Staircases
    • Measure Around Obstacles
    • Measure Circles & Arcs
    • Measure Buildings & Rooms
    • Import Moasure CSV Data into Uvision (Realtime Landscaping Architect)
    • Cómo importar un MFile en la app Moasure
  • API
    • API de Enlace de Aplicación
    • REST API
  • INTEGRACIONES
    • Scribe
    • ArcSite
    • MeasureSquare
Con tecnología de GitBook
En esta página
  • Single Measurement
  • Layers
  • Viewing Trees and Sprinkler Locations

¿Te fue útil?

Exportar como PDF
  1. CASOS DE USO

Measure Tree or Sprinkler Locations on a Lawn

You might wonder how you can measure locations of trees or sprinklers inside a space, for instance the position of several trees on a lawn. We'll address this use case in this guide.

AnteriorCómo medir un jardín complejoSiguienteMeasure Volume and 3D Terrain

¿Te fue útil?

There are two ways you could achieve this. You can achieve this using a single measurement or by first completing a measurement and then adding a layer. We will explain both options and their advantages and disadvantages below, starting with single measurement.

Single Measurement

1. Measure the Lawn Perimeter - by measuring the lawn perimeter. - Return to the start point without ending the measurement. 2. Capture Tree Locations - Change the path type to . Move towards the first tree and at the tree’s location. Repeat this process until all tree locations are captured. If you cannot reach a tree location within the range, you can switch to ignore path before moving to the next location and stop in between. The stops in between will then be marked as ignore points so you can distinguish them visually from the other points. You can also post measurement. 3. Complete Measurement - End the measurement once all tree locations are marked.

Layers

  1. Measure the Lawn Perimeter - by measuring the lawn perimeter. - Return to the start point and the measurement.

  2. Add a New Layer - Add a new layer to the measurement by tapping on the "Layers" Icon in the right bottom corner of the app and then tapping on "Add Layer". - You will be prompted to place the device at the shared origin. This is the start point of the first measurement (layer). - Once you place the device down and it's stationary at the shared origin, you will be prompted to move anywhere along the first origin edge. - The above two steps allows the Moasure device and Moasure App to correctly align your new layer to your first layer. Whilst completing these steps you will be in , so you will be prompted to change to a different path once completing those steps, so that the app can start drawing your measurement.

  3. Capture Tree Locations - Change the path type to . Move towards the first tree and at the tree’s location. Repeat this process until all tree locations are captured. If you cannot reach a tree location within the range, you can switch to ignore path before moving to the next location and stop in between. The stops in between will then be marked as ignore points so you can distinguish them visually from the other points. You can also post measurement.

  4. Complete Measurement - End the measurement once all tree locations are marked.

Viewing Trees and Sprinkler Locations

1. View in the App - In the app, you’ll see both the lawn perimeter and points representing tree locations on the drawing. If you've used a single measurement, they will appear on a single layer. If you've used Layers, they will appear on separate layers. In all cases, they will both be visible on the canvas by default, however you can choose to hide either when using Layers. The other benefit of using layers is that you can break up your measurement over time and save your progress between measurements, so that you just need to redo one layer if you make a mistake on the second layer rather than the whole measurement. A disadvantage of using layers could be that more care needs to be taken when starting the new layer to accurately align the new layer to the base layer. If this is not done well, the angle could be off. You can weigh these trade offs against each other to determine the best option for your project. - Tap on any point, whether on the perimeter layer or points layer, to. 2. View on PDF - If you wish to view coordinates on a PDF export, label the points before exporting. Coordinates of points measured using Points Path or Ignore Path that are not labeled, will not show on the PDF Export. If coordinate visibility on the PDF isn’t essential, you can skip labelling; the points will still appear visually on the drawing. - If you've labelled points, their respective coordinates and text label will be displayed on the “Labelled Points” section of the PDF.

Start
place the device
6-8 second recommended time
ignore points
Start
end
place the device
6-8 second recommended time
ignore points
view their respective x, y, z coordinates
Points Path
Ignore Path
Points Path